Filters
Loading…temperature sensors
Temperature sensors for ALPS EXCLUSIVE URBAN V2 heat pumps are used to measure and transmit important temperature values within the system. These sensors support the heat pump controller and help ensure safe, stable and efficient operation.
When replacing a temperature sensor, always check the original sensor type, sensor value, material version, cable length, plug connection and mounting position. This helps prevent incorrect readings, fault messages and improper heat pump control.
Chico CC.T94 - 5K copper temperature sensor
Item no. 600010EAN 8721225900990
Request access
In stock
Added
Chico CC.T98 - 5K plastic temperature sensor
Item no. 600011EAN 8721225901003
Request access
In stock
Added
Chico CC.T186 - 5K copper temperature sensor 10 m
Item no. 600012EAN 8721225901010
Request access
In stock
Added
Chico CC.T257 - 50K high-temperature sensor
Item no. 600013EAN 8721225901027
Request access
In stock
Added
Chico CC.T43 - 5K copper temperature sensor
Item no. 600014EAN 8721225901034
Request access
Op nalevering
Added
Chico CC.T245 - 5K copper temperature sensor
Item no. 600015EAN 8721225901041
Request access
In stock
Added
Temperature sensors for ALPS EXCLUSIVE URBAN V2 LINE heat pumps
Temperature sensors for the ALPS EXCLUSIVE URBAN V2 LINE are used to measure and transmit temperature values within the heat pump. Depending on the version, these sensors can be used for supply and return temperature, outdoor temperature, evaporator temperature, water-side measurements or domestic hot water control.
The correct temperature sensor selection depends on the series, unit type, article number, connection, voltage, sensor type, measuring range, resistance characteristic, connector, cable length, mounting position and technical version. Always check whether the sensor matches the original component and is placed in the correct position in the system.
Important checks for temperature sensors
- Check whether the temperature sensor is suitable for the relevant ALPS EXCLUSIVE URBAN V2 LINE heat pump and exact unit type.
- Compare the article number, sensor type, measuring range, resistance characteristic, connector layout, cable length and mounting position with the original sensor.
- Inspect the sensor for cable breakage, moisture, corrosion, damaged insulation, loose connectors or illogical temperature display.
- Check error codes, current temperature values, operating status and switching moments before replacing the temperature sensor.
- Check related components such as PCB, wiring harness, connectors, water-side circuit, evaporator position and control system.
Application, replacement and technical attention points
A temperature sensor is usually checked or replaced when the heat pump displays abnormal temperatures, shows error codes, switches incorrectly, cycles frequently or responds unstably during heating, cooling, defrosting or domestic hot water production. The cause may also be wiring, moisture in connectors or a deviation in the measured circuit.
Installation and diagnosis must be carried out by a qualified technician. After replacement, connectors, cable routing, mounting position, measured value, resistance characteristic, error codes and system operation must be checked again. An incorrect sensor value can affect control, safety, efficiency and operational reliability of the heat pump.
Frequently asked questions about temperature sensors
What is a temperature sensor used for in a heat pump?
A temperature sensor measures temperature values and transmits them to the control system. The heat pump uses this information for control, safety, diagnosis and switching moments.
When should a temperature sensor be replaced?
A temperature sensor should be replaced when it gives abnormal values, causes error codes, is damaged or no longer communicates reliably with the control system after diagnosis.
Does every temperature sensor fit every URBAN V2 LINE heat pump?
No, the correct version depends on the series, unit type, article number, connection, voltage, sensor type, measuring range, resistance characteristic, connector, cable length, mounting position and technical version.
Can an error code also be caused by wiring or connectors?
Yes, error codes or illogical temperature values can also be caused by cable breakage, moisture, corrosion, loose connectors, a defective PCB or a problem in the measured circuit.
Can a temperature sensor be installed without a technician?
For correct diagnosis and safe installation, a qualified technician is recommended. The technician checks measured values, resistance characteristic, connection, mounting position, error codes and operation after replacement.