Filters
Loading…Circuit boards
PCBs for ALPS EXCLUSIVE URBAN V2 heat pumps are used for electronic control, actuation and communication within the system. This includes main PCBs, secondary PCBs, control PCBs and electric coils, each with a specific function in the heat pump controller.
When replacing a PCB, always check the original article number, PCB code, connector layout, software compatibility, supply voltage and application within the relevant URBAN V2 model. This helps prevent incorrect control, communication issues and faults after installation.
Chico PW58467 CC1010B - Heat pump PCB 2.8 kW
Item no. 600004EAN 8721225900921
Request access
Low stock
Added
Chico - PW58343 PCB
Item no. 600035EAN 8721225901294
Request access
In stock
Added
Chico PW58384-1
Item no. 600034EAN 8721225901287
Request access
In stock
Added
Chico - PW58393 PCB
Item no. 600031EAN 8721225901263
Request access
In stock
Added
Chico PW58392-1 CC902 - Heat pump PCB
Item no. 600095EAN 8721225901256
Request access
Low stock
Added
Chico - PW58383-1 PCB
Item no. 600025EAN 8721225901157
Request access
In stock
Added
Sanhua electromagnetic coil AC220–240V
Item no. 600022EAN 8721225901119
Request access
In stock
Added
Sanhua expansion valve coil DC12V - 1 m
Item no. 600021EAN 8721225901102
Request access
In stock
Added
Chico PW58362 CC1211A - Current and power detection PCB
Item no. 600005EAN 8721225900938
Request access
In stock
Added
Chico - PW58382-1 PCB
Item no. 600040EAN 8721225901331
Request access
Low stock
Added
PCBs for ALPS EXCLUSIVE URBAN V2 LINE heat pumps
PCBs for the ALPS EXCLUSIVE URBAN V2 LINE are used for electronic control, communication and actuation within the heat pump. Depending on the version, PCBs can process signals from sensors, control panels, safety devices and control components.
The correct PCB selection depends on the series, unit type, article number, connection, voltage, PCB code, software version, hardware version, connector layout, phase version, mounting position and technical version. Always check whether the PCB matches the original component and is compatible with the other electronics in the heat pump.
Important checks for PCBs
- Check whether the PCB is suitable for the relevant ALPS EXCLUSIVE URBAN V2 LINE heat pump and exact unit type.
- Compare the article number, PCB code, software version, hardware version, connector layout, phase version, supply voltage and mounting position with the original PCB.
- Inspect the PCB for burn damage, moisture, corrosion, loose solder joints, damaged connectors, discoloration or visible component defects.
- Check error codes, supply voltage, fuses, communication signals, sensor readings and control of connected components before replacing the PCB.
- Check related components such as sensors, signal cables, control panel, fan motor, circulation pump, valves, compressor control and inverter module.
Application, replacement and technical attention points
A PCB is usually checked or replaced when the heat pump does not start correctly, has no communication, shows error codes, does not control components or processes illogical measured values. However, a PCB fault can also be caused by defective peripheral components, short circuit, moisture, incorrect supply voltage or damaged wiring.
Installation and diagnosis must be carried out by a qualified technician. After replacement, connectors, grounding, supply voltage, parameters, software compatibility, error codes, communication and operation of connected components must be checked again. With electronic parts, electrostatic damage and incorrect connection must be prevented.
Frequently asked questions about PCBs
What is a PCB used for in a heat pump?
A PCB processes signals and controls components within the heat pump. These include sensors, fans, pumps, valves, safety devices, control panels and communication between control components.
When should a PCB be replaced?
A PCB should be replaced when diagnosis confirms that the board is defective and the fault is not caused by power supply, wiring, sensors, fuses, motors or other connected components.
Does every PCB fit every URBAN V2 LINE heat pump?
No, the correct version depends on the series, unit type, article number, connection, voltage, PCB code, software version, hardware version, connector layout, phase version, mounting position and technical version.
Can a PCB fault also be caused by another component?
Yes, error codes or failure can also be caused by sensors, signal cables, connectors, fuses, power supply issues, motors, inverter module, moisture or short circuit in connected components.
Can a PCB be installed without a technician?
For correct diagnosis and safe installation, a qualified technician is recommended. The technician checks power supply, connectors, grounding, parameters, communication and heat pump operation after replacement.