Filters
Loading…Control circuit board
A control PCB for an ALPS EXCLUSIVE Urban V2 heat pump is an important part of the electronic control system. The PCB processes signals from sensors, the control panel and safety devices, and controls components such as the compressor, fan, pump or valves.
When replacing a control PCB, always check the original PCB type, article number, connections, software compatibility and application within the relevant Urban V2 model. This helps prevent communication issues, incorrect control and faults after installation.
Chico PW58467 CC1010B - Heat pump PCB 2.8 kW
Item no. 600004EAN 8721225900921
Request access
Low stock
Added
Chico - PW58383-1 PCB
Item no. 600025EAN 8721225901157
Request access
In stock
Added
Chico PW58392-1 CC902 - Heat pump PCB
Item no. 600095EAN 8721225901256
Request access
Low stock
Added
Chico - PW58393 PCB
Item no. 600031EAN 8721225901263
Request access
In stock
Added
Chico - PW58343 PCB
Item no. 600035EAN 8721225901294
Request access
In stock
Added
Chico - PW58382-1 PCB
Item no. 600040EAN 8721225901331
Request access
Low stock
Added
Control PCB for ALPS EXCLUSIVE URBAN V2 LINE heat pumps
A control PCB for the ALPS EXCLUSIVE URBAN V2 LINE is used for the central electronic control of the heat pump. The board processes signals from sensors, control panels and safety devices and controls components such as fans, valves, circulation pumps, electrical coils and control modules.
The correct control PCB selection depends on the series, unit type, article number, connection, voltage, PCB code, software version, hardware version, connector layout, phase version, mounting position and technical version. Always check whether the control PCB matches the original component and is compatible with the other electronics in the heat pump.
Important checks for a control PCB
- Check whether the control PCB is suitable for the relevant ALPS EXCLUSIVE URBAN V2 LINE heat pump and exact unit type.
- Compare the article number, PCB code, software version, hardware version, connector layout, phase version, supply voltage and mounting position with the original board.
- Inspect the board for burn damage, moisture, corrosion, loose solder joints, damaged connectors, discoloration or visible component defects.
- Check error codes, power supply, grounding, fuses, communication signals, parameter settings and control of connected components.
- Check related components such as sensors, signal cables, control panel, secondary PCB, motherboard, fan motor, pumps, valves and safety circuits.
Application, replacement and technical attention points
A control PCB is usually checked or replaced when the heat pump does not start correctly, has no communication, shows error codes, does not control components or processes illogical measured values. The cause may also be defective peripheral components, damaged wiring, incorrect supply voltage, moisture or short circuit in connected parts.
Installation and diagnosis must be carried out by a qualified technician. After replacement, connectors, power supply, grounding, parameters, software compatibility, error codes, communication and operation of all connected components must be checked again. With electronic components, careful handling is important to prevent electrostatic damage or incorrect connection.
Frequently asked questions about a control PCB
What is a control PCB used for in a heat pump?
A control PCB processes signals and controls important components of the heat pump. These include sensors, fans, pumps, valves, safety devices, control panels and communication modules.
When should a control PCB be replaced?
A control PCB should be replaced when diagnosis confirms that the board is defective and the fault is not caused by power supply, wiring, sensors, fuses, motors or other connected components.
Does every control PCB fit every URBAN V2 LINE heat pump?
No, the correct version depends on the series, unit type, article number, connection, voltage, PCB code, software version, hardware version, connector layout, phase version, mounting position and technical version.
Can a fault also be caused by another component?
Yes, error codes or failure can also be caused by sensors, signal cables, connectors, power supply issues, fuses, fan motors, pumps, valves, inverter modules or short circuit in peripheral components.
Can a control PCB be installed without a technician?
For correct diagnosis and safe installation, a qualified technician is recommended. The technician checks power supply, grounding, connectors, parameters, communication and complete system operation after replacement.