Filters
Loading…Circuit boards
At Hewa you will find PCBs and electrical control components for ALPS EXCLUSIVE ARTIC and URBAN LINE heat pumps. This category is intended for installers, service technicians and technical buyers looking for PCBs for control, actuation, diagnostics, maintenance or replacement.
PCBs are an important part of the electronic heat pump control system. Always check the exact heat pump model, article number, EAN, type code, connection, phase version, PCB function and software compatibility of the original component before ordering.
Chico PW58467 CC1010B - Heat pump PCB 2.8 kW
Item no. 600004EAN 8721225900921
Request access
Low stock
Added
Chico - PW58343 PCB
Item no. 600035EAN 8721225901294
Request access
In stock
Added
Chico PW58384-1
Item no. 600034EAN 8721225901287
Request access
In stock
Added
Chico - PW58393 PCB
Item no. 600031EAN 8721225901263
Request access
In stock
Added
Chico PW58392-1 CC902 - Heat pump PCB
Item no. 600095EAN 8721225901256
Request access
Low stock
Added
Chico - PW58383-1 PCB
Item no. 600025EAN 8721225901157
Request access
In stock
Added
Sanhua electromagnetic coil AC220–240V
Item no. 600022EAN 8721225901119
Request access
In stock
Added
Sanhua expansion valve coil DC12V - 1 m
Item no. 600021EAN 8721225901102
Request access
In stock
Added
Chico PW58362 CC1211A - Current and power detection PCB
Item no. 600005EAN 8721225900938
Request access
In stock
Added
Chico - PW58382-1 PCB
Item no. 600040EAN 8721225901331
Request access
Low stock
Added
PCBs for ALPS EXCLUSIVE ARTIC and URBAN LINE heat pumps
PCBs are used in compatible ALPS EXCLUSIVE ARTIC and URBAN LINE heat pumps for electronic control, regulation and communication within the unit. Depending on the configuration, a PCB may handle functions such as compressor control, fan control, sensor readings, safety monitoring, communication with the control panel and control of hydraulic components.
For diagnosis, service or replacement, the PCB must match the exact technical configuration of the heat pump. The correct spare part depends on the series, unit type, article number, PCB type, software version, connection, supply voltage, connector layout, phase configuration, mounting position and technical configuration of the unit.
Important checks for PCBs
- Always check whether the PCB is suitable for the relevant ALPS EXCLUSIVE ARTIC or URBAN LINE version.
- Compare the article number, PCB code, software version, hardware version, connector positions and plug connections with the original PCB.
- Inspect the PCB for burn damage, moisture ingress, loose solder joints, damaged components, corrosion or discoloured terminals.
- Look for fault codes, communication problems, non-responsive components, failure of sensors, fans, compressor control or control panel.
- Also check the power supply, fuses, wiring harness, connectors, sensors, motors, inverter module and external components before replacing the PCB.
Application, replacement and technical attention points
A PCB may need to be replaced when the heat pump no longer starts correctly, continues to show fault codes, no longer controls components or no longer communicates with other control parts. Overvoltage, moisture, short circuit, incorrect wiring or defective peripheral components can also damage the PCB.
Work on electrical control components must be carried out by a qualified technician. After replacement, supply voltage, grounding, connector positions, parameters, software settings, communication, fault messages, component control and full operation of the heat pump controller should be checked.
Frequently asked questions about PCBs
What is a PCB used for in a heat pump?
A PCB processes signals, measured values and control functions within the heat pump. It can read sensors, control components, monitor safety functions and communicate with the control panel.
When should a PCB be replaced?
Replacement may be required in case of burn damage, moisture ingress, defective component control, communication problems, fault codes, damaged connectors or when diagnosis clearly confirms that the PCB is defective.
Does every PCB fit every ALPS EXCLUSIVE heat pump?
No, PCBs differ by series, unit type and technical configuration. Always check the article number, PCB code, software version, connection, connector layout, phase configuration and mounting position before ordering a spare part.
Can a fault also be caused by another component?
Yes, a fault may appear to be caused by a defective PCB while the actual cause is sensors, wiring, connectors, fuses, fan motors, compressor control or external components. A complete diagnosis is therefore required.
Can a PCB be installed by the end user?
No, installation and diagnosis of PCBs must be carried out by a qualified technician. Electrical safety, parameter settings, connector positions and system checks must be performed correctly.